UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 1
Default Testing H4 car bulb with multimeter

Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?

Thank you for any info.
  #2   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 258
Default Testing H4 car bulb with multimeter

"Stan" wrote in message
...
Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?

Thank you for any info.


If this is a "normal" halogen bulb like this
http://www.bestrestproducts.com/cele...4-HP_240-1.jpg

then no resistance would mean it is dead.

I think the pinouts are, looking at the bottom of the bulb with a terminal
on the left, right and top

Left terminal is common
Top terminal is low beam
Right terminal is high beam

So you need to measure between the left pin and the top, then the left and
the right.

Sparks...


  #3   Report Post  
Posted to uk.d-i-y,uk.rec.cars.maintenance,uk.rec.cars.misc
external usenet poster
 
Posts: 1,136
Default Testing H4 car bulb with multimeter

On Mon, 15 Jan 2007 01:00:21 -0000, Sparks wrote:

then no resistance would mean it is dead.


Quick get a patent on it for room temperature super conductivity. B-)

Bulbs are either a few ohms (working) or lots of ohms as in open circuit
(bust).

--
Cheers
Dave. pam is missing e-mail



  #4   Report Post  
Posted to uk.d-i-y,uk.rec.cars.maintenance,uk.rec.cars.misc
external usenet poster
 
Posts: 258
Default Testing H4 car bulb with multimeter

"Dave Liquorice" wrote in message
ll.com...
On Mon, 15 Jan 2007 01:00:21 -0000, Sparks wrote:

then no resistance would mean it is dead.


Quick get a patent on it for room temperature super conductivity. B-)

Bulbs are either a few ohms (working) or lots of ohms as in open circuit
(bust).

--
Cheers
Dave. pam is missing e-mail


Lol, Arse!

That's what I actually meant of course!


  #5   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 1,285
Default Testing H4 car bulb with multimeter

Stan wrote:
Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?


Very low indeed, and too low to measure with any accuracy with a normal
multimeter.

Say it's 55 watts at 13.8 volts. Resistance is voltage squared over
power, so 13.8^2 / 55 i.e. about 3.5 ohms when hot. When measuring cold
you can divide that by about 15, so about 0.2 ohm.

HTH
--
Andy


  #6   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 82
Default Testing H4 car bulb with multimeter


"Stan" wrote in message
...
Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?

Thank you for any info.


provided there is contact between any two pins it will work (because the
neutral is common)

mrcheerful


  #7   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 43,017
Default Testing H4 car bulb with multimeter

In article ,
Stan wrote:
Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?


Just measured one - 0.4 ohm. I'd guess it will vary somewhat between makes
and depending on ambient temperature.

--
*I have plenty of talent and vision. I just don't care.

Dave Plowman London SW
To e-mail, change noise into sound.
  #8   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 410
Default Testing H4 car bulb with multimeter

Stan pretended :
Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?


Thank you for any info.


Usually you can check them without a meter - just give the lamp a sharp
tap with your finger tip and see if the filament vibrates excessively,
as if broken.

If you really want to test it...

One of the three pins is common - connected to both filaments, the
other two are the main and dip beam connections. With a multimeter and
assuming the lamp is good, you should get a value of a few ohms between
any two pins. The two pins which have the higher value between them,
means that the third pin is the common.

With care you could test the lamp across a 12v battery. Similar to
above, the two pins which produce the dimmest light out, means that the
third unconnected pin is the common.

--

Regards,
Harry (M1BYT) (L)
http://www.ukradioamateur.co.uk


  #9   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 5,175
Default Testing H4 car bulb with multimeter


Stan wrote:

Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?


Zero resistance (short circuit) or as close to it as you're likely to
be able to measure with a cheap meter and simple test leads.

You might be able to see the diference when you have two filaments in
series, but you're unlikely to measure any difference between the high
and dipped beams, even though they're of different powers.

Resistance of them goes up when they're hot, but a meter won't deliver
enough power to notice this. Working resistance of a bulb is v^2/w, so
about an ohm or two. They'll be under an ohm when cold.

  #10   Report Post  
Posted to uk.rec.cars.maintenance,uk.rec.cars.misc,uk.d-i-y
external usenet poster
 
Posts: 1
Default Testing H4 car bulb with multimeter

"Stan" wrote in message
...
Using a multimeter, what resistances would I expect to get from a
working H4 car headlight bulb?


See responses below but why would you want to?


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
9V battery testing; Thevenin equivalent; car headlamps. Adam Funk Electronics Repair 22 August 2nd 06 10:57 AM
multimeter that has a transistor test socket for hfe testing tom Electronics 60 March 6th 06 05:44 PM
Testing Rechargeable Batteries with a Multimeter [email protected] Home Repair 4 January 21st 06 04:13 AM
Bug Light Bulb---any bulb for outside use that are not yellow? Patty Amas Home Ownership 5 November 3rd 04 10:23 PM
Laws requiring portable appliance testing and electrical installation testing if any? Z UK diy 9 June 14th 04 12:00 PM


All times are GMT +1. The time now is 09:15 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"