Home Repair - Page 6

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

		Home » DIYbanter forum » Do - it - Yourself
Home Repair

Home

Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems.

Popular Tags: Home Repair

advice, air, basement, bathroom, best, ceiling, concrete, dishwasher, door, drain, dryer, electric, electrical, fan, floor, free, furnace, garage, gas, heat, heater, help, home, house, insulation, kitchen, light, old, paint, pipe, pool, pressure, problem, pump, question, questions, repair, replacement, roof, shower, switch, tile, toilet, wall, washer, water, window, wiring, wont, wood

Page 6 of 2751

Threads in Forum : Home Repair

Forum Tools

Search this Forum

Thread / Thread Starter	Last Post	Replies	Views
Crown Moulding Picture by Kate[_5_] I am not having any luck sending a pic to this newsgroup. I can use tinypic and get it down to a thumb print, but then it asks for this groups'...	March 10th 10 01:50 AM by The Daring Dufas[_6_]	4	12
How to Protect Trailer Fenders by DerbyDad03 What can I, in the comfort of my own home, apply to the fronts of the fenders on this trailer so that the paint doesn't get chipped off by stones and...	March 10th 10 01:20 AM by clare@snyder.on.ca	9	13
update by Mike On Mar 8, 3:48*pm, The Daring Dufas wrote: Existential Angst wrote: "Paul Oman" wrote...	March 10th 10 01:14 AM by The Daring Dufas[_6_]	1	13
Home circuit reading 40V all of a sudden? by Mike Reed Hi, I plugged our vacuum in to the GFI in the kitchen, and when I turned it on, I heard a "pop" and assumed it was the GFI that needed to be reset... ( 1 2 3 ... Last Page)	March 10th 10 12:45 AM by Ralph Mowery	33	47
it's 2010 and linux is still dead on the desktop by Throckmorton E. Pouch On Tue, 9 Mar 2010 12:32:26 -0500, One Shot, One Kill...	March 9th 10 08:51 PM by Throckmorton E. Pouch	0	8
Dropping Trees on Septic Field by jamesgangnc[_3_] I need to take down a couple gumball trees. The gumballs are driving us crazy. Unless there is a way to "neuter" them they have go to go. One is... ( 1 2 3)	March 9th 10 07:10 PM by jamesgangnc[_3_]	26	39
Here is a Picture of My New Crown Moulding by Kate[_5_] Thanks everyone who helped me figure out how to send a pic to this site. I hope this works. Kate	March 9th 10 03:20 PM by salty@dog.com	9	19
cordless drill not working by badgolferman My Ryobi 14.4 volt drill is not working. The battery is fully charged at 14.5 volts and the flashlight that comes with it is bright but the drill... ( 1 2 3 ... Last Page)	March 9th 10 02:20 PM by Jim Yanik	105	106
Attachment of Rail to Concrete or Motar Pillar ?? by James I need to attach a rail to my 92 year old Mom's front steps. I am using a 1 inch galvanized pipe, 60 inches long, with 90 degree elbows on each...	March 9th 10 06:55 AM by Rudy	6	24
Subfloor: plywood vs. OSB by ls02 Should I use plywood or T&G OSB for subfloor in new addition I am building? The addition is on second story, floors are 2 X 8 16 O.C. I checked... ( 1 2 3)	March 9th 10 06:51 AM by Rudy	21	24
Crown Molding Project Done by Kate[_5_] To everyone who helped me with tips on crown molding my special thanks. A friend helped me Saturday and Sunday. It was a big project, but the...	March 9th 10 05:57 AM by hr(bob) hofmann@att.net	2	7
From Ceramic Tile to Wood Laminate by MikeL[_3_] I'm taking up tile and plan on laying down a laminate floor. How critical is getting up all of the thin-set from the plywood? and if so, any...	March 9th 10 05:28 AM by Joe	5	7
Stihl MS200T stalling on idle after running by dean I have a Stihl ms200t chainsaw that keeps on trying to sputter out after doing a cut. If I pulse the throttle I can usually get it back to life but I...	March 9th 10 05:17 AM by Joe	4	19
Laundry tub faucet by ng_reader I have a need to replace my laundry tub and faucet with a faucet that looks like this...	March 9th 10 04:31 AM by Lefty[_2_]	1	12
Adobe Homes by JIMMIE My friend and I were discussing building adobe home in areas where adobe would not normally be used, Like here in North Carolina. We are aware of its... ( 1 2)	March 9th 10 02:34 AM by krw@att.bizzzzzzzzzzzz	19	37
Start Earning $15 - $105 by pianist Data Entry for Ads Placing Working via Internet, Job Training Provided Signup Now http://www.gogonai.info/?id=pianist	March 9th 10 12:21 AM by pianist	0	7
Underfloor radiator by Sam Takoy Hi, My contractor mentioned to me (but couldn't remember the brand) that there exist hot water radiators that go between the joists on the floor...	March 8th 10 09:16 PM by Sam Takoy	8	18
Building jamb for existing doors by Wayne Whitney Hello, I have two salvaged doors which I would like to make into double doors for a closet. So I have to build a new jamb for them, and I... ( 1 2)	March 8th 10 09:13 PM by Wayne Whitney	18	41
Finding reliable Furniture Removal Contractors in Australia by groups CQ Did you know that you can get dependable furniture removal service quotes for FREE while saving time, money and effort? That is right. At Compare...	March 8th 10 05:48 PM by Metspitzer	1	11
click me by madhan Hello, i am new member of this group please clic the following page it will be usefull to you http://123maza.com/78/healthyfitness/	March 8th 10 05:33 PM by madhan	0	5

Page 6 of 2751

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts vB code is On Smilies are On [IMG] code is On HTML code is Off

All times are GMT +1. The time now is 02:03 AM.