|
|
Roll Top Desk by
Lew Hodgett[_4_]
Watched an old NTW rerun of Norm making a roll top desk
The construction is pretty straight forward, but still would require a
lot of man hours to...
( 1 2)
|
|
17 |
18 |
|
|
|
O/T: Ho Hum by
Lew Hodgett[_4_]
Palin resigns as governor of Alaska.
That woman does OK until she opens her mouth.
Lew
( 1 2 3 ... Last Page)
|
|
44 |
45 |
|
|
|
|
0 |
1 |
|
|
|
Sliding dovetail angle for sliding by
Larry C
Hi
Does it make a difference what angle dovetail bit I use for a sliding
dovetail. I am (finally) making a few cribbage boards that the bottom...
|
|
4 |
11 |
|
|
|
|
Today 01:55 PM
by Bill 
|
33 |
53 |
|
|
|
Wooden Knitting Needles by
Tanus
After a DAGS, SWMBO bought some needles from this place in Nova Scotia:
http://www.lismoresheepfarmwoolshop.com/needles/index.htm,
and is happy with...
( 1 2 3)
|
Today 01:55 PM
by dpb
|
20 |
33 |
|
|
|
O/T: 79 Pound Carp by
Lew Hodgett[_5_]
Just ran a piece on TV about a guy catching a 79 pound carp with a bow
and arrow in Iowa.
Anywhere close to you Morris?
Listed as a predator fish...
( 1 2 3 ... Last Page)
|
|
31 |
40 |
|
|
|
Are we lost by
PDQ
Where the heck is every body????? :-(
P D Q
( 1 2 3)
|
|
22 |
23 |
|
|
|
What is it? Set 290 by
Joseph Gwinn
In article ,
"Steve R." wrote:
"DoN. Nichols" wrote in message
...
|
|
1 |
14 |
|
|
|
How Do You Know When It's Finished by
Tom Watson
The great Florentine bronze master, Ghiberti, had a man in the yard
behind his shop whose sole task was to polish the finished pieces.
The story...
|
|
5 |
10 |
|
|
|
OT - CNN Breaking News by
RonB[_2_]
The state of California just announced that Michael Jackson could not
be buried within the boundaries of the state of California. During
autopsy it...
|
|
6 |
10 |
|
|
|
Happy camper by
TDDriver
I finally had reason to try out my n3ew (to me)Delta thickness planer as
I needed to bring a 3/4 inch board down to 5/8. Sweet!!! Now I have...
|
|
1 |
2 |
|
|
|
Rockwell Table Saw Restoration by
rockymtns99
I just bought a Rockwell Model 10 Contractor table saw and am
currently getting it ready to use. I want to tear it down and clean
it, paint the CI...
|
|
5 |
11 |
|
|
|
good vise? by
Kerry Montgomery
Hello all,
Just broke one of the jaw inserts in my Craftsman 5" bench vise. Out of
warranty, no replacement parts available. Was wondering what...
( 1 2 3)
|
|
22 |
24 |
|
|
|
Jigs by
TDDriver
I've just spend the better part of an hour watching the youtube videos
of Matthias Wandel's tenoning, slot mortising and box joint jigs. I
think...
|
Yesterday 04:34 PM
by Tanus
|
3 |
14 |
|
|
|
|
|
63 |
64 |
|
|
|
|
|
5 |
15 |
|
|
|
|
|
2 |
6 |
|
|
|
Wenge and yellow interior by
dwolf[_2_]
I have worked with Wenge many times before, with some yellow inside that
does turn brown pretty quickly..
I have some 8/4 now that has a lot of...
|
|
1 |
6 |
|
|
|
FS: 3 HP Delta Unisaw motor. by
Mark Rance
This motor is from Delta. I have had it for many years but it has never
been used or even attached to a saw.
I am in Colorado Springs, CO.
Please...
|
|
0 |
9 |
