Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 17
Default Oil Remover receipe

Any diy's for this stuff? I've heard "whiting" and solvent, but,
what the heck is "whiting"? And which solvent?

The commercial is about $18 for 24 oz. Like to make a couple of
gallons.


thanks
  #2   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 408
Default Oil Remover receipe

On concrete I sweep with gasoline then cover with rice hulls for about 10 minutes and sweep it all up. Been re - using the same bucket of hulls for about 20 years. Works on shop floor and driveway.
Ivan Vegvary
  #3   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 450
Default Oil Remover receipe

Whiting is calcium carbonate usually mined from chalk deposits.
It's main use is as an absorbent. Fullers earth or diatomaceous earth will
probably work just as well.
The solvent depends on what your removing the oil from.
If it's your tie, I would use carbo chlor.
If it is your driveway, I would use kerosene.

Paul K. Dickman

"gary" wrote in message
...
Any diy's for this stuff? I've heard "whiting" and solvent, but,
what the heck is "whiting"? And which solvent?

The commercial is about $18 for 24 oz. Like to make a couple of
gallons.


thanks



  #4   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 18,538
Default Oil Remover receipe

On Mon, 21 Apr 2014 19:06:47 -0500, "Paul K. Dickman"
wrote:

Whiting is calcium carbonate usually mined from chalk deposits.
It's main use is as an absorbent. Fullers earth or diatomaceous earth will
probably work just as well.
The solvent depends on what your removing the oil from.
If it's your tie, I would use carbo chlor.
If it is your driveway, I would use kerosene.

Paul K. Dickman


Or better yet, mineral spirits. Kero is a light oil, so always leaves
a bit of oil behind.

"gary" wrote in message
.. .
Any diy's for this stuff? I've heard "whiting" and solvent, but,
what the heck is "whiting"? And which solvent?

The commercial is about $18 for 24 oz. Like to make a couple of
gallons.


thanks



  #5   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 2
Default Oil Remover receipe

On 2014-04-21, Ivan Vegvary wrote:

On concrete I sweep with gasoline then cover with rice hulls for
about 10 minutes and sweep it all up. Been re - using the same
bucket of hulls for about 20 years. Works on shop floor and
driveway. Ivan Vegvary


I hope that you do not smoke at the same time


  #6   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 327
Default Oil Remover receipe

On Mon, 21 Apr 2014 20:13:39 -0500, Ignoramus29188
wrote:

On 2014-04-21, Ivan Vegvary wrote:

On concrete I sweep with gasoline then cover with rice hulls for
about 10 minutes and sweep it all up. Been re - using the same
bucket of hulls for about 20 years. Works on shop floor and
driveway. Ivan Vegvary


I hope that you do not smoke at the same time


Ain't that the truth.

Reminds me of when Dad ran a bug catcher by the barn in southeast
Texas. The bug catcher bag wouldn't hold them. Ended up with a
crawling pile that filled a wheelbarrow. To kill them, Dad dumped on
gasoline. Later that day, he scooped them up and dumped them in the
burn barrel (we used to burn trash). Even later, he took out the
trash, lit it, and promptly got knocked down when all the little bug
bodies exploded. He said he was covered up with bug bits.

So I hope there's a lid on those rice hulls.

Pete Keillor
  #7   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 2
Default Oil Remover receipe

On 2014-04-22, Pete Keillor wrote:
On Mon, 21 Apr 2014 20:13:39 -0500, Ignoramus29188
wrote:

On 2014-04-21, Ivan Vegvary wrote:

On concrete I sweep with gasoline then cover with rice hulls for
about 10 minutes and sweep it all up. Been re - using the same
bucket of hulls for about 20 years. Works on shop floor and
driveway. Ivan Vegvary


I hope that you do not smoke at the same time


Ain't that the truth.

Reminds me of when Dad ran a bug catcher by the barn in southeast
Texas. The bug catcher bag wouldn't hold them. Ended up with a
crawling pile that filled a wheelbarrow. To kill them, Dad dumped on
gasoline. Later that day, he scooped them up and dumped them in the
burn barrel (we used to burn trash). Even later, he took out the
trash, lit it, and promptly got knocked down when all the little bug
bodies exploded. He said he was covered up with bug bits.

So I hope there's a lid on those rice hulls.

Pete Keillor


I was pumping **** (sewage) a couple of days ago with a gasoline
pump.

At some point a little plug came off the pump, and I was promptly
sprayed by a very healthy dose of **** that came through that hole.

i
  #8   Report Post  
Posted to rec.crafts.metalworking
SnA SnA is offline
external usenet poster
 
Posts: 3
Default Oil Remover receipe

gary wrote:
Any diy's for this stuff? I've heard "whiting" and solvent, but,
what the heck is "whiting"? And which solvent?

The commercial is about $18 for 24 oz. Like to make a couple of
gallons.


thanks


I use Virginia Solvent No. 10 on concrete. Pour some on. Work it was a
floor brush. Hose it off. IIRC, about $20/g.
  #9   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 1,624
Default Oil Remover receipe

On 4/21/2014 1:24 PM, gary wrote:
Any diy's for this stuff? I've heard "whiting" and solvent, but,
what the heck is "whiting"? And which solvent?

The commercial is about $18 for 24 oz. Like to make a couple of
gallons.


thanks



Remove oil from clothes? Use "Lestoil".
  #10   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 18,538
Default Oil Remover receipe

On Tue, 22 Apr 2014 18:08:48 -0400, Tom Gardner Mars@Tacks wrote:

On 4/21/2014 1:24 PM, gary wrote:
Any diy's for this stuff? I've heard "whiting" and solvent, but,
what the heck is "whiting"? And which solvent?

The commercial is about $18 for 24 oz. Like to make a couple of
gallons.


thanks



Remove oil from clothes? Use "Lestoil".

For small grease stains I "dry clean" with Brake Klean.


  #15   Report Post  
Posted to rec.crafts.metalworking
external usenet poster
 
Posts: 3,984
Default Oil Remover receipe

On Monday, April 21, 2014 1:24:56 PM UTC-4, gary wrote:
Any diy's for this stuff? I've heard "whiting" and solvent, but,

what the heck is "whiting"? And which solvent?



The commercial is about $18 for 24 oz. Like to make a couple of

gallons.





thanks


I use Dawn dish detergent for oil. It works to remove oil from birds

Dan
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Limescale remover Brian Gaff[_2_] UK diy 12 March 12th 14 09:51 AM
rust remover bob UK diy 3 June 13th 10 09:20 AM
Pitch Remover? David Starr Woodworking 17 December 17th 06 08:44 PM
Tried finding the receipe Brent Beal Woodworking 4 December 12th 06 01:36 PM
Sealant remover? Part P UK diy 4 August 4th 06 02:21 PM


All times are GMT +1. The time now is 02:47 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"