Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
I own a generic handtruck/dolly with 10 inch dia pneumatic wheels.
The primary use of the dolly is to move appliances (not enough use to justify getting a real $$ appliance dolly). My dolly is 22 inch wide (from outside edge of tire to tire) and I am concerned about stability when moving things such as fridges tipping over. I have decided to split the hand truck and widen it about 6 inches and at the same time increase the depth of the base plate. Before I do this work, I thought maybe I should buy a “Bigfoot” dolly with 13 in. dia wheels. http://www.harborfreight.com/cpi/cta...emnumber=37520 Does anyone have experience with this type of a dolly – Harbor Freight frequently has these on sale for about $40. Will this dolly with the larger dia wheels go up steps easier. I would still end up splitting and widening the bigfoot dolly since it also is only 22 inches wide. |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
.... Does anyone have experience with this type of a dolly – Harbor Freight frequently has these on sale for about $40. Will this dolly with the larger dia wheels go up steps easier. I would still end up splitting and widening the bigfoot dolly since it also is only 22 inches wide. We have four of these. My biggest issue is the tires go flat often. Second issue is they get lost constantly. We need four just to keep one put away. otherwise they are great for moving stuff. To go up stairs, you need two operators. The bottom guy is the strong one, he lifts. The top guy pulls back balances and holds the gain. Then repeat. Don't get your tire so big that it won't just sit on a step. Karl |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
I have a similar one, nothing wrong with them, tires need to be pumped
often. When I looked, I found the harbor Freight one to be wimpy and instead bought a stronger one (USA made) from McMaster-Carr. The price difference was not much. i On 2008-11-06, Karl Townsend wrote: ... Does anyone have experience with this type of a dolly – Harbor Freight frequently has these on sale for about $40. Will this dolly with the larger dia wheels go up steps easier. I would still end up splitting and widening the bigfoot dolly since it also is only 22 inches wide. We have four of these. My biggest issue is the tires go flat often. Second issue is they get lost constantly. We need four just to keep one put away. otherwise they are great for moving stuff. To go up stairs, you need two operators. The bottom guy is the strong one, he lifts. The top guy pulls back balances and holds the gain. Then repeat. Don't get your tire so big that it won't just sit on a step. Karl -- Due to extreme spam originating from Google Groups, and their inattention to spammers, I and many others block all articles originating from Google Groups. If you want your postings to be seen by more readers you will need to find a different means of posting on Usenet. http://improve-usenet.org/ |
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Nov 6, 9:04*am, "Karl Townsend"
wrote: We have four of these. My biggest issue is the tires go flat often. I've got one, and while it's a pain when the tires are flat, it's trivial to pump them back up. It is embarrasing to show up with one flat tire! And the inflated tires make a world of difference in moving over mud. I first truly appreciated this during a rainy spring in British Columbia :-). I got mine like ten years ago and it is still going strong. Second issue is they get lost constantly. Isn't that like the Yogi Berra-ism "nobody goes there anymore, it's too crowded"? If it's getting lost constantly, that means it's the one that everybody uses! Tim. |
#6
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
"Larry Jaques" wrote in message ... On Thu, 6 Nov 2008 05:38:42 -0800 (PST), the infamous scrawled the following: I own a generic handtruck/dolly with 10 inch dia pneumatic wheels. The primary use of the dolly is to move appliances (not enough use to justify getting a real $$ appliance dolly). My dolly is 22 inch wide (from outside edge of tire to tire) and I am concerned about stability when moving things such as fridges tipping over. I have decided to split the hand truck and widen it about 6 inches and at the same time increase the depth of the base plate. Before I do this work, I thought maybe I should buy a "Bigfoot" dolly with 13 in. dia wheels. http://www.harborfreight.com/cpi/cta...emnumber=37520 Does anyone have experience with this type of a dolly - Harbor Freight frequently has these on sale for about $40. Will this dolly with the larger dia wheels go up steps easier. I would still end up splitting and widening the bigfoot dolly since it also is only 22 inches wide. I own the 10-incher, too, and adore it. The one time I used the larger one, it was even easier to work. You won't even know when you ride up over a curb or small steps. g The 13" wheels are on sale for $10 each now, and 13.5-inchers are $13. search www.harborfreight.com for ' 13" tire '. Go for it. -- Everything I did in my life that was worthwhile I caught hell for. -- Earl Warren i have the one with 10" wheels, and yes, they tend to go flat frequently. however, they ride over the desert sand pretty well and goes over small rocks without noticing them. don't know how they are for standard stairs, but they do go up short curbs well. i did bend the bottom of it moving a 300 lb boulder, so don't take their load maximum very seriously. regards, charlie cave creek, az |
#7
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
|
#8
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
"charlie" wrote:
i have the one with 10" wheels, and yes, they tend to go flat frequently. however, they ride over the desert sand pretty well and goes over small rocks without noticing them. don't know how they are for standard stairs, but they do go up short curbs well. Anyone try putting Slime in the tires? Wes |
#9
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Sun, 09 Nov 2008 17:41:40 -0500, Wes
wrote: "charlie" wrote: i have the one with 10" wheels, and yes, they tend to go flat frequently. however, they ride over the desert sand pretty well and goes over small rocks without noticing them. don't know how they are for standard stairs, but they do go up short curbs well. Anyone try putting Slime in the tires? Wes I have one of those cheap wagons with similar wheels. Suppose to be good for 1000 lbs or something, snort! Anyway, tightening up the valve cores did wonders to slow down the leakage. Only have to air them up a couple times per year now. -- Leon Fisk Grand Rapids MI/Zone 5b Remove no.spam for email |
#10
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
Leon Fisk wrote:
Anyone try putting Slime in the tires? Wes I have one of those cheap wagons with similar wheels. Suppose to be good for 1000 lbs or something, snort! Anyway, tightening up the valve cores did wonders to slow down the leakage. Only have to air them up a couple times per year now. I put some slime in my 20 year old walk behind snowblower tires. Tubeless and age cracked. I'm hoping it helps. So far, leaks down fast but I haven't actually made a pass down the 200 foot driveway. That should coat them well if nothing more. Wes -- "Additionally as a security officer, I carry a gun to protect government officials but my life isn't worth protecting at home in their eyes." Dick Anthony Heller |
#11
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Mon, 10 Nov 2008 19:03:03 -0500, Wes wrote:
Leon Fisk wrote: Anyone try putting Slime in the tires? Wes I have one of those cheap wagons with similar wheels. Suppose to be good for 1000 lbs or something, snort! Anyway, tightening up the valve cores did wonders to slow down the leakage. Only have to air them up a couple times per year now. I put some slime in my 20 year old walk behind snowblower tires. Tubeless and age cracked. I'm hoping it helps. So far, leaks down fast but I haven't actually made a pass down the 200 foot driveway. That should coat them well if nothing more. Wes Why in h**l do they use tubeless tires on snow blowers, wheelbarrows etc.? After a few years, rust penetrates the bead area and the only remedy is an inner tube which then lasts until the outer casing rots off. Both my snow blower (1985) and wheelbarrow (older) still have the original tires with inner tubes installed. It is not like these are high speed, heat sensitive uses, at least not in my case! Gerry :-)} London, Canada |
#12
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Mon, 10 Nov 2008 22:00:10 -0500, the infamous Gerald Miller
scrawled the following: On Mon, 10 Nov 2008 19:03:03 -0500, Wes wrote: Leon Fisk wrote: Anyone try putting Slime in the tires? Wes I have one of those cheap wagons with similar wheels. Suppose to be good for 1000 lbs or something, snort! Anyway, tightening up the valve cores did wonders to slow down the leakage. Only have to air them up a couple times per year now. I put some slime in my 20 year old walk behind snowblower tires. Tubeless and age cracked. I'm hoping it helps. So far, leaks down fast but I haven't actually made a pass down the 200 foot driveway. That should coat them well if nothing more. Wes Why in h**l do they use tubeless tires on snow blowers, wheelbarrows etc.? After a few years, rust penetrates the bead area and the only remedy is an inner tube which then lasts until the outer casing rots off. Both my snow blower (1985) and wheelbarrow (older) still have the original tires with inner tubes installed. It is not like these are high speed, heat sensitive uses, at least not in my case! Does everyone here FEEEL for Gerry? How about a group "Awwwwww!"? gd&r Let's see, a new tube costs $4USD. A new wheel, bearings, tire, and tube assembly costs $5 or $10USD. What to do? What to do? Our HF is your Princess, right? Seek and ye might find, sir Ger. -- Never lose sight of this important truth, that no one can be truly great until he has gained a knowledge of himself, a knowledge which can only be acquired by occasional retirement. -- Johann Georg von Zimmermann |
#13
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Mon, 10 Nov 2008 19:41:34 -0800, Larry Jaques
wrote: On Mon, 10 Nov 2008 22:00:10 -0500, the infamous Gerald Miller scrawled the following: On Mon, 10 Nov 2008 19:03:03 -0500, Wes wrote: Leon Fisk wrote: Anyone try putting Slime in the tires? Wes I have one of those cheap wagons with similar wheels. Suppose to be good for 1000 lbs or something, snort! Anyway, tightening up the valve cores did wonders to slow down the leakage. Only have to air them up a couple times per year now. I put some slime in my 20 year old walk behind snowblower tires. Tubeless and age cracked. I'm hoping it helps. So far, leaks down fast but I haven't actually made a pass down the 200 foot driveway. That should coat them well if nothing more. Wes Why in h**l do they use tubeless tires on snow blowers, wheelbarrows etc.? After a few years, rust penetrates the bead area and the only remedy is an inner tube which then lasts until the outer casing rots off. Both my snow blower (1985) and wheelbarrow (older) still have the original tires with inner tubes installed. It is not like these are high speed, heat sensitive uses, at least not in my case! Does everyone here FEEEL for Gerry? How about a group "Awwwwww!"? gd&r Let's see, a new tube costs $4USD. A new wheel, bearings, tire, and tube assembly costs $5 or $10USD. What to do? What to do? Our HF is your Princess, right? Seek and ye might find, sir Ger. I do have a spare tire for my wheelbarrow from Princess Auto - cost $2 about 4 years ago, haven't needed to install it yet. OTOH, Tires for the snow blower will cost me $35 each. As to changing to a less expensive size - you wanna come take the old wheels off the axle? Bring your cutting torch cause they are permanently rusted in place! Gerry :-)} London, Canada |
#14
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
I got tired of forgetting to air up the tires before using the hand
truck so I bought replacement 10" tires/wheels from HF when they had them on sale for $3.99 - they hold air **much** longer that the tires that came with the hand truck (Home Depot I think). On Nov 9, 5:41*pm, Wes wrote: "charlie" wrote: i have the one with 10" wheels, and yes, they tend to go flat frequently.. however, they ride over the desert sand pretty well and goes over small rocks without noticing them. don't know how they are for standard stairs, but they do go up short curbs well. Anyone try putting Slime in the tires? Wes |
#15
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Mon, 10 Nov 2008 23:25:13 -0500, the infamous Gerald Miller
scrawled the following: On Mon, 10 Nov 2008 19:41:34 -0800, Larry Jaques wrote: On Mon, 10 Nov 2008 22:00:10 -0500, the infamous Gerald Miller scrawled the following: On Mon, 10 Nov 2008 19:03:03 -0500, Wes wrote: Leon Fisk wrote: Anyone try putting Slime in the tires? Wes I have one of those cheap wagons with similar wheels. Suppose to be good for 1000 lbs or something, snort! Anyway, tightening up the valve cores did wonders to slow down the leakage. Only have to air them up a couple times per year now. I put some slime in my 20 year old walk behind snowblower tires. Tubeless and age cracked. I'm hoping it helps. So far, leaks down fast but I haven't actually made a pass down the 200 foot driveway. That should coat them well if nothing more. Wes Why in h**l do they use tubeless tires on snow blowers, wheelbarrows etc.? After a few years, rust penetrates the bead area and the only remedy is an inner tube which then lasts until the outer casing rots off. Both my snow blower (1985) and wheelbarrow (older) still have the original tires with inner tubes installed. It is not like these are high speed, heat sensitive uses, at least not in my case! Does everyone here FEEEL for Gerry? How about a group "Awwwwww!"? gd&r Let's see, a new tube costs $4USD. A new wheel, bearings, tire, and tube assembly costs $5 or $10USD. What to do? What to do? Our HF is your Princess, right? Seek and ye might find, sir Ger. I do have a spare tire for my wheelbarrow from Princess Auto - cost $2 about 4 years ago, haven't needed to install it yet. "Good shew." he said, in his best Ed Sullivan voice. OTOH, Tires for the snow blower will cost me $35 each. As to changing to a less expensive size - you wanna come take the old wheels off the axle? Bring your cutting torch cause they are permanently rusted in place! Sounds like a self-inflicted wound due to lack of maintenance to me, sir. Shameful! P.S: What's a "snow blower"? -- Never lose sight of this important truth, that no one can be truly great until he has gained a knowledge of himself, a knowledge which can only be acquired by occasional retirement. -- Johann Georg von Zimmermann |
#16
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
Larry Jaques wrote:
Let's see, a new tube costs $4USD. A new wheel, bearings, tire, and tube assembly costs $5 or $10USD. What to do? What to do? The wheelbarrow is easy, my wide profile snowblower tires look like they spot welded the halves together after inserting on either side of the tire. I can't buy the tire from searz, have to buy tires and rim. Humm. Wes |
#17
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Fri, 14 Nov 2008 18:50:23 -0500, the infamous Wes
scrawled the following: Larry Jaques wrote: Let's see, a new tube costs $4USD. A new wheel, bearings, tire, and tube assembly costs $5 or $10USD. What to do? What to do? The wheelbarrow is easy, my wide profile snowblower tires look like they spot welded the halves together after inserting on either side of the tire. I can't buy the tire from searz, have to buy tires and rim. Humm. You said the "I just let the magic smoke out!" word, Wes; Searz. Go buy something worth _fixing_, eh? Sheesh! Better yet, build one yourself/rebuild the axle. -- If we all did the things we are capable of doing, we would literally astound ourselves. -- Thomas A. Edison |
#18
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
Wes wrote: Larry Jaques wrote: Let's see, a new tube costs $4USD. A new wheel, bearings, tire, and tube assembly costs $5 or $10USD. What to do? What to do? The wheelbarrow is easy, my wide profile snowblower tires look like they spot welded the halves together after inserting on either side of the tire. I can't buy the tire from searz, have to buy tires and rim. Humm. I just bought a tire & rim for my wheelbarrow at Harbor Freight for $20. -- http://improve-usenet.org/index.html aioe.org, Goggle Groups, and Web TV users must request to be white listed, or I will not see your messages. If you have broadband, your ISP may have a NNTP news server included in your account: http://www.usenettools.net/ISP.htm There are two kinds of people on this earth: The crazy, and the insane. The first sign of insanity is denying that you're crazy. |
#19
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
replying to Wes, Alan Lashway wrote:
yeah it didn't work -- for full context, visit http://www.polytechforum.com/metalwo...ck-150340-.htm |
#20
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On 2/15/2017 11:18 PM, Alan Lashway wrote:
replying to Wes, Alan Lashway wrote: yeah it didn't work I notice the thread is from 2008, so regarding the flats on the Harbor Freight tires, there seems to be no need to tell you about my success using Slime Tire sealant to keep air in them. --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus |
#21
Posted to rec.crafts.metalworking
|
|||
|
|||
Using a "bigfoot" (large dia wheel) dolly/handtruck
On Thu, 16 Feb 2017 05:18:02 GMT, Alan Lashway
wrote: replying to Wes, Alan Lashway wrote: yeah it didn't work That thread was from 2008. Um, did it take you 9 years to widen a hand truck frame? g I guess I shouldn't talk. I have some 6-y/o projects on the shelf... -- In order to become the master, the politician poses as the servant. --Charles de Gaulle |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
For women who desire the traditional 12-marker dials, the "Faceto,""Juro" and "Rilati" all add a little more functionality, without sacrificingthe diamonds. | Woodworking | |||
size &/or "Wonder" wheel, grinding disk, or blade on TS for safe cutting of acrylic light shield plastic | Woodworking | |||
Making a "wheel of fortune " prize wheel | UK diy | |||
Making a "wheel of fortune " prize wheel | UK diy |