|
Garage Door Opener-Capacitor gone bad?
About a month ago my Liftmaster 1265 stopped running. It would just hum for
about 2 seconds and stop. Liftmaster said the limit switch has been overrun, so I played with that. When I move the limit back, the opener hummed for 2 seconds, paused, and then hummed for 2 seconds with a slightly different pitch. Someone here said the problem was probably a leaking capacitor. I took the cover off, but the capacitor looked fine. But when I touched the capacitor the opener suddenly started running. It was okay for 2 days, then stopped again. I touched the capacitor again and it ran okay for 5 minutes, then stopped. Now touching does not help. I figured there was loose wire, but I sure can't find one. Liftmaster says it is probably a bad capacitor for $20; and if not that, a bad logic board for $85. Does a bad capacitor make sense? Could touching a bad capacitor make it run for a while? Obviously they won't be taking the capacitor back if it doesn't help. This is so so frustrating. |
"Samuel Warren" wrote in message ... Sounds like to me that PCB connection has broke lose from it's solder connection. Have a skilled electronics friend resolder the connection to the PCB board for you. Can you elaborate on what a PCB connection is, and how I identify it? All the wires are firmly attached, but if it is something smaller i wouldn't have seen it. Thanks. |
Someone here said the problem was probably a leaking capacitor. I took the
cover off, but the capacitor looked fine. But when I touched the capacitor the opener suddenly started running. It was okay for 2 days, then stopped again. I touched the capacitor again and it ran okay for 5 minutes, then stopped. Now touching does not help. I figured there was loose wire, but I sure can't find one. Liftmaster says it is probably a bad capacitor for $20; and if not that, a bad logic board for $85. Does a bad capacitor make sense? Could touching a bad capacitor make it run for a while? Obviously they won't be taking the capacitor back if it doesn't help. --------------- I'm can't help you troubleshoot the problem, but if you want to try a new capacitor, take the old one along with the wiring schematic to an electronics store. You can get a new one for under a dollar. |
It's the Electronic or logic board. Is the cap soldered to that?
This message was written on 100% recycled spam. SAM "toller" wrote in message ... "Samuel Warren" wrote in message ... Sounds like to me that PCB connection has broke lose from it's solder connection. Have a skilled electronics friend resolder the connection to the PCB board for you. Can you elaborate on what a PCB connection is, and how I identify it? All the wires are firmly attached, but if it is something smaller i wouldn't have seen it. Thanks. |
toller wrote:
About a month ago my Liftmaster 1265 stopped running. It would just hum for about 2 seconds and stop. Liftmaster said the limit switch has been overrun, so I played with that. When I move the limit back, the opener hummed for 2 seconds, paused, and then hummed for 2 seconds with a slightly different pitch. Someone here said the problem was probably a leaking capacitor. I took the cover off, but the capacitor looked fine. But when I touched the capacitor the opener suddenly started running. It was okay for 2 days, then stopped again. I touched the capacitor again and it ran okay for 5 minutes, then stopped. Now touching does not help. I figured there was loose wire, but I sure can't find one. Liftmaster says it is probably a bad capacitor for $20; and if not that, a bad logic board for $85. Does a bad capacitor make sense? Could touching a bad capacitor make it run for a while? Obviously they won't be taking the capacitor back if it doesn't help. This is so so frustrating. Hi, How is the capacitor mounted? On the body of motor? On a logic board? Any lead wires from capacitor? Then where is the wires going? No wires and mounted on a logic board, then vibration cracked solder joints causing intermittent problem. Resolder them and reinforce it with a drop of epoxy. Good luck, Tony P.S. You can't tell whether capacitor is good or bad by just looking. |
|
Abe wrote:
Someone here said the problem was probably a leaking capacitor. I took the cover off, but the capacitor looked fine. But when I touched the capacitor the opener suddenly started running. It was okay for 2 days, then stopped again. I touched the capacitor again and it ran okay for 5 minutes, then stopped. Now touching does not help. I figured there was loose wire, but I sure can't find one. Liftmaster says it is probably a bad capacitor for $20; and if not that, a bad logic board for $85. Does a bad capacitor make sense? Could touching a bad capacitor make it run for a while? Obviously they won't be taking the capacitor back if it doesn't help. --------------- I'm can't help you troubleshoot the problem, but if you want to try a new capacitor, take the old one along with the wiring schematic to an electronics store. You can get a new one for under a dollar. Hi, If it's starting cap for the motor. It will cost more than a dollar for sure. Tony |
toller wrote: About a month ago my Liftmaster 1265 stopped running. It would just hum for about 2 seconds and stop. Liftmaster said the limit switch has been overrun, so I played with that. When I move the limit back, the opener hummed for 2 seconds, paused, and then hummed for 2 seconds with a slightly different pitch. Someone here said the problem was probably a leaking capacitor. I took the cover off, but the capacitor looked fine. But when I touched the capacitor the opener suddenly started running. It was okay for 2 days, then stopped again. I touched the capacitor again and it ran okay for 5 minutes, then stopped. Now touching does not help. Did you remove the cover without disconnecting the AC power first? That can be risky, not only because of the potential for electric shock but also for the opener to start accidentally and grab your finger or hair. I'd first disconnect the AC and see if the connections to the motor capacitor are loose. Reseat any push-on spade connectors, and tighten any screw eyelet connectors. If that doesn't help, then you may have a bad motor capacitor or a bad connection elsewhere. Vibration from the motor can make solder joints crack on the printed circuit board (PCB), but the cracks can be microscopic, so some technicians simply resolder almost everything (start with connectors and larger, heavier component connections). Since the motor capacitor is an oil-filled one, it can be tested fairly well with just an ordinary volt-ohm meter -- see www.repairfaq.org for instructions and also for safety advice. These capacitors are available from almost any electrical supply but not from electronic supplies, which rarely carry oil-filled capacitors. Liftmaster is made by Chamberlain, which also makes Sears Craftsman openers, and Sears is sometimes cheaper for parts. |
toller wrote: About a month ago my Liftmaster 1265 stopped running. It would just hum for about 2 seconds and stop. Liftmaster said the limit switch has been overrun, so I played with that. When I move the limit back, the opener hummed for 2 seconds, paused, and then hummed for 2 seconds with a slightly different pitch. Someone here said the problem was probably a leaking capacitor. I took the cover off, but the capacitor looked fine. But when I touched the capacitor the opener suddenly started running. It was okay for 2 days, then stopped again. I touched the capacitor again and it ran okay for 5 minutes, then stopped. Now touching does not help. Did you remove the cover without disconnecting the AC power first? That can be risky, not only because of the potential for electric shock but also for the opener to start accidentally and grab your finger or hair. I'd first disconnect the AC and see if the connections to the motor capacitor are loose. Reseat any push-on spade connectors, and tighten any screw eyelet connectors. If that doesn't help, then you may have a bad motor capacitor or a bad connection elsewhere. Vibration from the motor can make solder joints crack on the printed circuit board (PCB), but the cracks can be microscopic, so some technicians simply resolder almost everything (start with connectors and larger, heavier component connections). Since the motor capacitor is an oil-filled one, it can be tested fairly well with just an ordinary volt-ohm meter -- see www.repairfaq.org for instructions and also for safety advice. These capacitors are available from almost any electrical supply but not from electronic supplies, which rarely carry oil-filled capacitors. Liftmaster is made by Chamberlain, which also makes Sears Craftsman openers, and Sears is sometimes cheaper for parts. |
electronics stores don't carry that size caps. i have an older liftmaster like
this and same type problem , i tracked it down to the contacts were covered w/ carbon and other crap cleaned and fixed my problem. . then one of torsion springs broke |
Garage Door Opener-Capacitor gone bad?
replying to toller, Matt wrote:
The capacitor can cause it not to run because that is what gives the motor the initial start you can get a capacitor at homedepot or at any garage door dealer just be sure and put the wires in the same place -- for full context, visit http://www.homeownershub.com/mainten...ad-591327-.htm |
Garage Door Opener-Capacitor gone bad?
On Saturday, February 5, 2005 at 10:34:50 AM UTC-6, toller wrote:
About a month ago my Liftmaster 1265 stopped running. It would just hum for about 2 seconds and stop. Liftmaster said the limit switch has been overrun, so I played with that. When I move the limit back, the opener hummed for 2 seconds, paused, and then hummed for 2 seconds with a slightly different pitch. Someone here said the problem was probably a leaking capacitor. I took the cover off, but the capacitor looked fine. But when I touched the capacitor the opener suddenly started running. It was okay for 2 days, then stopped again. I touched the capacitor again and it ran okay for 5 minutes, then stopped. Now touching does not help. I figured there was loose wire, but I sure can't find one. Liftmaster says it is probably a bad capacitor for $20; and if not that, a bad logic board for $85. Does a bad capacitor make sense? Could touching a bad capacitor make it run for a while? Obviously they won't be taking the capacitor back if it doesn't help. This is so so frustrating. IF he doesn't have it working after 11 years, it isn't worthwhile replying to him |
Garage Door Opener-Capacitor gone bad?
On Tuesday, October 18, 2016 at 10:44:05 AM UTC-5, Matt wrote:
replying to toller, Matt wrote: The capacitor can cause it not to run because that is what gives the motor the initial start you can get a capacitor at homedepot or at any garage door dealer just be sure and put the wires in the same place -- Unfortunately, 10 years ago, Toller was killed when his garage door came down on him and crushed his throat. Investigators determined that he had been screwing around with the opener and had bypassed all the safeties. He was survived by a wife, 3 ex-wives, 14 children and 346 gerbils. The gerbils really miss him. It was a very tragic event. (́_̀) [8~{} Uncle Sad Monster |
Garage Door Opener-Capacitor gone bad?
On Tue, 18 Oct 2016 20:52:30 -0700 (PDT), Uncle Monster
wrote: Unfortunately, 10 years ago, Toller was killed when his garage door came down on him and crushed his throat. Investigators determined that he had been screwing around with the opener and had bypassed all the safeties. He was survived by a wife, 3 ex-wives, 14 children and 346 gerbils. The gerbils really miss him. It was a very tragic event. (??_??) [8~{} Uncle Sad Monster .... sadly, all the gerbils have since died |
Garage Door Opener-Capacitor gone bad?
replying to hrhofmann, BobbyVee wrote:
Hilarious! -- for full context, visit https://www.homeownershub.com/mainte...ad-591327-.htm |
| All times are GMT +1. The time now is 05:59 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright 2004 - 2014 DIYbanter