Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
 
Posts: n/a
Default reverse condensate pump?

Hello,
Recently inspecting my gas furnace I noticed water leaking out of the
condensate pump. So I pulled it out to figure out what is going on.
Here is what I found: The unit runs when empty but will not run when
water is added. I put it in the sink, turned it on (with no water in
it and it started running), I turned the tap on and started filling it
with water. It ran and did pump water out until it filled up to a
certain point then the pump stopped. It then overfilled and started
pouring water out of the fill hole.

Now I am no handy man. In fact I know very little about anything
having to do with my house (except the things I've learned since owning
a house these last 6 months) but does this pump seem like it is working
backwards? Shouldn't it pump with water in it and then stop when most
has been removed? Any ideas? There is a float switch and I reversed
the wires but that changed nothing. Ideas anyone.
Thank you for any suggestions.



  #2   Report Post  
BGBevill
 
Posts: n/a
Default

Hello,
Recently inspecting my gas furnace I noticed water leaking out of the
condensate pump. So I pulled it out to figure out what is going on.
Here is what I found: The unit runs when empty but will not run when
water is added. I put it in the sink, turned it on (with no water in
it and it started running), I turned the tap on and started filling it
with water. It ran and did pump water out until it filled up to a
certain point then the pump stopped. It then overfilled and started
pouring water out of the fill hole.

Now I am no handy man. In fact I know very little about anything
having to do with my house (except the things I've learned since owning
a house these last 6 months) but does this pump seem like it is working
backwards? Shouldn't it pump with water in it and then stop when most
has been removed? Any ideas? There is a float switch and I reversed
the wires but that changed nothing. Ideas anyone.
Thank you for any suggestions.





Take a closer look at the float arm that trips the micro switch to start the
pump. It should make the switch when the float rises. Something is amiss with
yours, or you have something very different from anything I have ever seen....

Bobby
  #4   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 1
Default reverse condensate pump?

replying to trevorcable, Mark Ash wrote:
I had the same issue. With my pump. Just randomly it switches from normal to
reverse operation. So I ripped it apart and found, inside the trigger there
is a copper clip that makes the connection between the power and the motor.
this tiny little clip is bowed upward until pressure is placed on its center
then it snaps to a downward bow. Kind of like those metal hair clips do.
What went wrong is the clip sets into the trigger in a way to keep it bowed
upward To fix it you'll need a nimble touch. but reset the clip into place and
make sure its in the correct position before closing up the trigger case.
Hope this helps.

--
for full context, visit http://www.homeownershub.com/mainten...mp-575218-.htm


  #5   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 14,845
Default reverse condensate pump?

On Friday, December 2, 2016 at 2:44:05 PM UTC-5, Mark Ash wrote:
replying to trevorcable, Mark Ash wrote:
I had the same issue. With my pump. Just randomly it switches from normal to
reverse operation. So I ripped it apart and found, inside the trigger there
is a copper clip that makes the connection between the power and the motor.
this tiny little clip is bowed upward until pressure is placed on its center
then it snaps to a downward bow. Kind of like those metal hair clips do.
What went wrong is the clip sets into the trigger in a way to keep it bowed
upward To fix it you'll need a nimble touch. but reset the clip into place and
make sure its in the correct position before closing up the trigger case.
Hope this helps.


The water has been leaking from the OP's pump for 12 years. The mold got so
bad that he had to move. He moved to a location where furnaces are not needed.

He does however, thank you for the advice on hair clip operation. He feels
(and looks) so much better now.


  #6   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 7,157
Default reverse condensate pump?

On Friday, December 2, 2016 at 2:09:53 PM UTC-6, DerbyDad03 wrote:
On Friday, December 2, 2016 at 2:44:05 PM UTC-5, Mark Ash wrote:
replying to trevorcable, Mark Ash wrote:
I had the same issue. With my pump. Just randomly it switches from normal to
reverse operation. So I ripped it apart and found, inside the trigger there
is a copper clip that makes the connection between the power and the motor.
this tiny little clip is bowed upward until pressure is placed on its center
then it snaps to a downward bow. Kind of like those metal hair clips do..
What went wrong is the clip sets into the trigger in a way to keep it bowed
upward To fix it you'll need a nimble touch. but reset the clip into place and
make sure its in the correct position before closing up the trigger case.
Hope this helps.


The water has been leaking from the OP's pump for 12 years. The mold got so
bad that he had to move. He moved to a location where furnaces are not needed.

He does however, thank you for the advice on hair clip operation. He feels
(and looks) so much better now.



Did he take his gerbils with him? He must be careful what part of the world he moved to because there are parts of the world where his neighbors might eat his gerbils. ヽ(ヅ)ノ

[8~{} Uncle Hungry Monster
  #7   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 14,845
Default reverse condensate pump?

On Friday, December 2, 2016 at 7:16:32 PM UTC-5, Uncle Monster wrote:
On Friday, December 2, 2016 at 2:09:53 PM UTC-6, DerbyDad03 wrote:
On Friday, December 2, 2016 at 2:44:05 PM UTC-5, Mark Ash wrote:
replying to trevorcable, Mark Ash wrote:
I had the same issue. With my pump. Just randomly it switches from normal to
reverse operation. So I ripped it apart and found, inside the trigger there
is a copper clip that makes the connection between the power and the motor.
this tiny little clip is bowed upward until pressure is placed on its center
then it snaps to a downward bow. Kind of like those metal hair clips do.
What went wrong is the clip sets into the trigger in a way to keep it bowed
upward To fix it you'll need a nimble touch. but reset the clip into place and
make sure its in the correct position before closing up the trigger case.
Hope this helps.


The water has been leaking from the OP's pump for 12 years. The mold got so
bad that he had to move. He moved to a location where furnaces are not needed.

He does however, thank you for the advice on hair clip operation. He feels
(and looks) so much better now.



Did he take his gerbils with him? He must be careful what part of the world he moved to because there are parts of the world where his neighbors might eat his gerbils. ヽ(ヅ)ノ

[8~{} Uncle Hungry Monster


I was going to mention the gerbils, but I didn't want to steal your thunder..

Cousin Considerate Monster
  #8   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 8,582
Default reverse condensate pump?

In alt.home.repair, on Fri, 02 Dec 2016 19:44:02 +0000, Mark Ash
m wrote:

replying to trevorcable, Mark Ash wrote:
I had the same issue. With my pump. Just randomly it switches from normal to
reverse operation. So I ripped it apart and found, inside the trigger there
is a copper clip that makes the connection between the power and the motor.
this tiny little clip is bowed upward until pressure is placed on its center
then it snaps to a downward bow. Kind of like those metal hair clips do.
What went wrong is the clip sets into the trigger in a way to keep it bowed
upward To fix it you'll need a nimble touch. but reset the clip into place and
make sure its in the correct position before closing up the trigger case.
Hope this helps.


This was a pretty good answer. I say that partly becuase it explains
what the problem is, instead of just saying, as so many HOH do, "I had
the same problem. "

Except that it's been so long since he posted this. I gather the people
in HOH can't see any dates? I think the HOH people should fix that.

I also wonder if they ever see our answers. No one ever replies to one.

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
condensate pump lifespan? Joe Shlabotnick Home Repair 2 October 9th 04 06:50 AM
Water Pump / Pressure Tank Problem !!!!!! James Nipper Home Repair 9 June 28th 04 03:13 AM
Water Pump / Pressure Tank Problem !!!!!! James Nipper Home Ownership 6 June 28th 04 03:13 AM
Low Water Pressure - pump stops at 20 psi - need advice Please Davis Leeman Home Repair 2 March 14th 04 03:57 PM
Backup Sump Pump Horror Story Harvey Krodin Home Repair 10 June 27th 03 03:59 PM


All times are GMT +1. The time now is 06:40 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"