Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Corey Dale
 
Posts: n/a
Default Craftsman snowblower problem!

Hello.

I have an older (about 20yrs from what I've read) Craftsman snow
thrower/blower (model "536-90520 HC2") with a problem. It is a
self-propelled model.

I bought the unit from the previous owner of my home. I tried it out
about a week ago (for the first time) and it wouldn't start. I took
it to a local shop for a tune-up, and they get it running great after
a minor carb cleaning.

I got it home and used it for the first time last night. It worked
great for the first half of my driveway, then all of a sudden the
wheel drive stopped working. The auger drive still works fine, the
engine still runs fine, but the 4 forward and 1 reverse gears don't do
anything anymore (no more self-proppeled)!!

Could anyone give me some advice/guidance on what the possible cause
could be? Would it be something I could fix easily myself?

Please respond by email and also here for anyone else that may be
having this problem.

Thanks,

Corey Dale
(remove the '.nospam')
  #2   Report Post  
George Macomber
 
Posts: n/a
Default Craftsman snowblower problem!

probally a broken drive gear
cotter pin





Hello.

I have an older (about 20yrs from what I've read) Craftsman snow
thrower/blower (model "536-90520 HC2") with a problem. It is a
self-propelled model.

I bought the unit from the previous owner of my home. I tried it out
about a week ago (for the first time) and it wouldn't start. I took
it to a local shop for a tune-up, and they get it running great after
a minor carb cleaning.

I got it home and used it for the first time last night. It worked
great for the first half of my driveway, then all of a sudden the
wheel drive stopped working. The auger drive still works fine, the
engine still runs fine, but the 4 forward and 1 reverse gears don't do
anything anymore (no more self-proppeled)!!

Could anyone give me some advice/guidance on what the possible cause
could be? Would it be something I could fix easily myself?

Please respond by email and also here for anyone else that may be
having this problem.

Thanks,

Corey Dale
(remove the '.nospam')

  #3   Report Post  
Bob M.
 
Posts: n/a
Default Craftsman snowblower problem!

A lot of the self-propelled snow blowers use a constantly variable drive
system that consists of a vertically-oriented flat plate, driven by a belt
from the engine on a horizontal shaft. Another wheel with a rubber tire on
it is pressed against the plate's flat surface and is arranged so it can
slide left or right. On one side of center, the machine will go forward, on
the other side it will go backward. The further out toward the edge you go,
the faster the machine moves. These components often get oil and/or grease
on them, so they only slip. Also, after 20+ years, the rubber has likely
dried out and no longer presses against the flat plate with enough pressure
to drive the wheels.

First step would be to clean the flat plate and rubber surface with
something like isopropyl alcohol to remove all the oil and grease. If you
can find some rubber roller restorer fluid, often used on old typewriters
and even some printers and tape decks, you could apply some of that to the
rubber tire. I don't think there's an adjustment you can make that will
bring the rubber tire any closer to the flat plate, but it might be possible
to loosen the plate's mounting screws and slide it on the shaft a bit closer
to the rubber tire-equipped drive mechanism. If all else fails, you'd have
to replace the rubber tire and/or the wheel it's mounted on if they're
inseparable.

This same mechanism is used on Toro, MTD, and most likely all of the under
$1200 snow blowers that have a solid rear axle and several forward and
reverse speeds.

Bob M.
======
"Corey Dale" wrote in message
m...
Hello.

I have an older (about 20yrs from what I've read) Craftsman snow
thrower/blower (model "536-90520 HC2") with a problem. It is a
self-propelled model.

I bought the unit from the previous owner of my home. I tried it out
about a week ago (for the first time) and it wouldn't start. I took
it to a local shop for a tune-up, and they get it running great after
a minor carb cleaning.

I got it home and used it for the first time last night. It worked
great for the first half of my driveway, then all of a sudden the
wheel drive stopped working. The auger drive still works fine, the
engine still runs fine, but the 4 forward and 1 reverse gears don't do
anything anymore (no more self-proppeled)!!

Could anyone give me some advice/guidance on what the possible cause
could be? Would it be something I could fix easily myself?

Please respond by email and also here for anyone else that may be
having this problem.

Thanks,

Corey Dale
(remove the '.nospam')



  #4   Report Post  
Corey Dale
 
Posts: n/a
Default Craftsman snowblower problem!

George Macomber wrote in message ...
probally a broken drive gear
cotter pin



Hello George, thanks for the reply.

That sounds like it might be the problem! It helped to jog my memory
about how the snowblower was acting before the tune-up, right after
the tune-up, and how its acting now.

Before the tuneup, when I would push the snowblower there was no noise
coming from the wheel assembly at all. After the tuneup, I noticed
that when I pushed the snowblower (when it wasn't running and in gear)
there was a noticable noise coming from it (I'm thinking now that it
was the gearbox turning as the wheels turned). After the drive
stopped working, the noise disappeared (so no connection between the
wheel axle and the drive-shaft going to the gearbox!).

Does that sound I have the problem identified?

Thanks again,
Corey



Hello.

I have an older (about 20yrs from what I've read) Craftsman snow
thrower/blower (model "536-90520 HC2") with a problem. It is a
self-propelled model.

I bought the unit from the previous owner of my home. I tried it out
about a week ago (for the first time) and it wouldn't start. I took
it to a local shop for a tune-up, and they get it running great after
a minor carb cleaning.

I got it home and used it for the first time last night. It worked
great for the first half of my driveway, then all of a sudden the
wheel drive stopped working. The auger drive still works fine, the
engine still runs fine, but the 4 forward and 1 reverse gears don't do
anything anymore (no more self-proppeled)!!

Could anyone give me some advice/guidance on what the possible cause
could be? Would it be something I could fix easily myself?

Please respond by email and also here for anyone else that may be
having this problem.

Thanks,

Corey Dale
(remove the '.nospam')

  #5   Report Post  
gg
 
Posts: n/a
Default Craftsman snowblower problem!

maybe the belt just broke , or the tension pulley isnt working and the belt
is just slipping on the pulley

"Bob M." wrote in message
...
A lot of the self-propelled snow blowers use a constantly variable drive
system that consists of a vertically-oriented flat plate, driven by a belt
from the engine on a horizontal shaft. Another wheel with a rubber tire on
it is pressed against the plate's flat surface and is arranged so it can
slide left or right. On one side of center, the machine will go forward,

on
the other side it will go backward. The further out toward the edge you

go,
the faster the machine moves. These components often get oil and/or grease
on them, so they only slip. Also, after 20+ years, the rubber has likely
dried out and no longer presses against the flat plate with enough

pressure
to drive the wheels.

First step would be to clean the flat plate and rubber surface with
something like isopropyl alcohol to remove all the oil and grease. If you
can find some rubber roller restorer fluid, often used on old typewriters
and even some printers and tape decks, you could apply some of that to the
rubber tire. I don't think there's an adjustment you can make that will
bring the rubber tire any closer to the flat plate, but it might be

possible
to loosen the plate's mounting screws and slide it on the shaft a bit

closer
to the rubber tire-equipped drive mechanism. If all else fails, you'd have
to replace the rubber tire and/or the wheel it's mounted on if they're
inseparable.

This same mechanism is used on Toro, MTD, and most likely all of the under
$1200 snow blowers that have a solid rear axle and several forward and
reverse speeds.

Bob M.
======
"Corey Dale" wrote in message
m...
Hello.

I have an older (about 20yrs from what I've read) Craftsman snow
thrower/blower (model "536-90520 HC2") with a problem. It is a
self-propelled model.

I bought the unit from the previous owner of my home. I tried it out
about a week ago (for the first time) and it wouldn't start. I took
it to a local shop for a tune-up, and they get it running great after
a minor carb cleaning.

I got it home and used it for the first time last night. It worked
great for the first half of my driveway, then all of a sudden the
wheel drive stopped working. The auger drive still works fine, the
engine still runs fine, but the 4 forward and 1 reverse gears don't do
anything anymore (no more self-proppeled)!!

Could anyone give me some advice/guidance on what the possible cause
could be? Would it be something I could fix easily myself?

Please respond by email and also here for anyone else that may be
having this problem.

Thanks,

Corey Dale
(remove the '.nospam')







  #6   Report Post  
Ron
 
Posts: n/a
Default Craftsman snowblower problem!

It could be that the drive belt for the wheels has come off the pulley. My
old snowblower which was similar to the Craftsman models had a vinyl cover
just behind the discharge chute and in front of the engine. Remove this
cover (snowblower engine OFF) and inspect the belt drive system by having
someone helping you by engaging and disengaging the drive clutch on the
handle of the snowblower.

You should see which belt is being engaged, or should I say, attempting to
be engaged. There is an idler arm assembly that keeps the belt on the
pulleys and also engages the power when the clutch lever is engaged. This is
where I would look for the belt to be disengaged as it is a place where a
lot of wear could have happened to the parts on a machine 20 years old.

If the belt assembly is engaging ok (belt gets tight when the clutch is
engaged) then as one other person suggested, look for the drive shear pin
assembly which will require the removal of the rear cover on the snowblower.
Good luck
--
Ron
Port Dover Ontario
"Corey Dale" wrote in message
m...
Hello.

I have an older (about 20yrs from what I've read) Craftsman snow
thrower/blower (model "536-90520 HC2") with a problem. It is a
self-propelled model.

I bought the unit from the previous owner of my home. I tried it out
about a week ago (for the first time) and it wouldn't start. I took
it to a local shop for a tune-up, and they get it running great after
a minor carb cleaning.

I got it home and used it for the first time last night. It worked
great for the first half of my driveway, then all of a sudden the
wheel drive stopped working. The auger drive still works fine, the
engine still runs fine, but the 4 forward and 1 reverse gears don't do
anything anymore (no more self-proppeled)!!

Could anyone give me some advice/guidance on what the possible cause
could be? Would it be something I could fix easily myself?

Please respond by email and also here for anyone else that may be
having this problem.

Thanks,

Corey Dale
(remove the '.nospam')


  #7   Report Post  
Corey Dale
 
Posts: n/a
Default Craftsman snowblower problem!

"Ron" wrote in message ...
It could be that the drive belt for the wheels has come off the pulley. My
old snowblower which was similar to the Craftsman models had a vinyl cover
just behind the discharge chute and in front of the engine. Remove this
cover (snowblower engine OFF) and inspect the belt drive system by having
someone helping you by engaging and disengaging the drive clutch on the
handle of the snowblower.

You should see which belt is being engaged, or should I say, attempting to
be engaged. There is an idler arm assembly that keeps the belt on the
pulleys and also engages the power when the clutch lever is engaged. This is
where I would look for the belt to be disengaged as it is a place where a
lot of wear could have happened to the parts on a machine 20 years old.

If the belt assembly is engaging ok (belt gets tight when the clutch is
engaged) then as one other person suggested, look for the drive shear pin
assembly which will require the removal of the rear cover on the snowblower.
Good luck
--
Ron
Port Dover Ontario


Hi again. Thanks to anyone who posted to help me out, as I managed to
identify and fix the problem!

I first opened up the shroud on the opposite end of the motor from the
pull cord. This shroud covered two belts - one for the auger system
and one for the engine. Both belts were in good shape, and were under
good contact pressure with the engine in gear and the auger drive
engaged.

I then opened up the cover over the wheel drive assembly. The problem
was immediately clear, as one of two chains in this housing had come
off it's gears. Apparently a free flywheel with gears that is used to
keep proper tnesion on the chain that drives the wheel had slipped
(not tightened enough during the tuneup, I suspect), giving two much
slack. The chain slipped off and so the snowblower wouldn't go! I
put the chain back on the sprockets, adjusted the small
flywhell/spocket as needed, and could tell even before I started it
back up that it was working fine as I could hear the sprockets turning
as I pushed the snowblower in neutral.

It started up with no problems, and went like the wind when I put it
in gear.

Thanks again for the help and ideas! It was a great learning
experience for me, and it was fascinating to see how simple the whole
drive system was (with the rotating disc and rubber wheel).

Regards,
Corey Dale
Edmonton, Alberta
"Home of the Heritage Classic Outdoor NHL Hockey Game!!"
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Craftsman 101.07403 12" Lathe Terry G Metalworking 12 March 20th 04 09:37 AM
New Craftsman RAS report Doug Winterburn Woodworking 18 March 11th 04 03:50 PM
craftsman lathes FS Charles A. Sherwood Metalworking 0 January 6th 04 04:35 PM
Boiler Problem Gradually Getting Worse Frank Davis UK diy 1 October 23rd 03 11:00 PM
Toshiba vertical problem David Wolff Electronics Repair 1 July 18th 03 10:41 PM


All times are GMT +1. The time now is 01:33 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"