Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
Just picked up my newly sharpened blades from the mower place. The repair
guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? |
#2
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
I wouldn't worry about the lawnmower man, just tighten the blades to 40ft/lb
indicated ( assuming that's the right spec) on the wrench and you will be fine. With an 18 inch wrench even a 90 pound weakling :-) should be able to get 40 ft/lb. I personally would just tighten them till they are tight without using a torque wrench but until you determine what tight means just trust the wrench. -- Mikey S. "JoeSpareBedroom" wrote in message ... Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? |
#3
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
"JoeSpareBedroom" wrote in message ... Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? Maybe he was thinking of a ratchet instead of the breaker bar ? As you have a torque wrench you know how much force 40 ft lbs is. About 30 pounds of force on the end of the 18 inch wrench. That is almost nothing. I don't worry too much about the tightning of the blades. I use some Felpro antiseize to make them easier to get off next time. Got chastised over here for doing it, but I have never had a blade to come off while running in 30 years. One thing, 40 ft lb with your wrench is just as much as with a much larger wrench. |
#4
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
On Aug 1, 4:36*pm, "JoeSpareBedroom" wrote:
Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? Even if its not torqued right it wont come off because of the rotation of the motor is oposite. 40 lb is nothing, a 3/8 does it, the guy doesnt know. |
#5
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
In article , "JoeSpareBedroom" wrote:
Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? He's full of beans. |
#6
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
JoeSpareBedroom wrote: Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? I'm guessing he either thought the bolts would go into aluminum threads that couldn't take any higher torque, or you wouldn't have anything to hold the blade in place while tighting the bolts and would be relying only on engine compression to resist the tightening. |
#7
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
he's talking out his ass. Or perhaps he meant just a standard 3/8 drive
ratchet. perhaps he didn't think they'd be long enough to get the leverage. s "JoeSpareBedroom" wrote in message ... Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? |
#8
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
On Fri, 1 Aug 2008 17:36:53 -0400, "JoeSpareBedroom"
wrote: Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. Sure, 100 pounds. Ten pounds. But what makes you think you can do 40 pounds? LOL It's 18" long, bigger than any breaker bar I have. What's this repair guy talking about? |
#9
Posted to alt.home.repair
|
|||
|
|||
Torque wrench question
"mm" wrote in message news On Fri, 1 Aug 2008 17:36:53 -0400, "JoeSpareBedroom" wrote: Just picked up my newly sharpened blades from the mower place. The repair guys said "Make damn sure you tighten the bolts right. There's no way to get the required 40 ft/lb torque with a 3/8" drive. With a breaker bar, yes, but not with a 3/8 torque wrench." I have a 3/8" drive Matco torque wrench with adjustments from 10 to 100 ft lbs. Sure, 100 pounds. Ten pounds. But what makes you think you can do 40 pounds? LOL I'm totally misguided. :-) |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Impact wrench torque | Metalworking | |||
Measuring torque on a motor with a leadscrew with a torque wrench | Metalworking | |||
Measuring torque on a motor with a leadscrew with a torque wrench | Metalworking | |||
Torque wrench | UK diy | |||
What's a torque wrench? | Home Repair |