Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 13
Default Outdoor timer running to fast

I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.

  #2   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 5,823
Default Outdoor timer running to fast


wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


Probably a faulty timer, but check to see if it has an automatic DST switch
that happened to trip if it is one hour even.


  #3   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 112
Default Outdoor timer running to fast

wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


That timer uses a simple synchronous clock motor timer that depends on the
60Hz AC power for accuracy. If the clock motor runs at all it is probably
keeping time. There is no "DST switch". I suspect an operator error.


  #4   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 5,040
Default Outdoor timer running to fast

In article ,
"Travis Jordan" wrote:

wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


That timer uses a simple synchronous clock motor timer that depends on the
60Hz AC power for accuracy. If the clock motor runs at all it is probably
keeping time. There is no "DST switch". I suspect an operator error.


That makes sense, but for some reason the cheapos suck at keeping time.
I bought three of them on sale one day, and two of them were typically
off by an hour or so after a day or two.
  #5   Report Post  
Posted to alt.home.repair
dpb dpb is offline
external usenet poster
 
Posts: 12,595
Default Outdoor timer running to fast

Travis Jordan wrote:
wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


That timer uses a simple synchronous clock motor timer that depends on the
60Hz AC power for accuracy. If the clock motor runs at all it is probably
keeping time. ...


The accuracy of the input doesn't guarantee the accuracy of the output
if it isn't manufactured under precise (enough) tolerances...

--



  #6   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 112
Default Outdoor timer running to fast

"dpb" wrote in message ...
Travis Jordan wrote:
wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


That timer uses a simple synchronous clock motor timer that depends on
the 60Hz AC power for accuracy. If the clock motor runs at all it is
probably keeping time. ...


The accuracy of the input doesn't guarantee the accuracy of the output if
it isn't manufactured under precise (enough) tolerances...


The synchronous motor drives a set of fixed tooth gears which in turn drive
the time display. "Manufacturing tolerances" won't cause the timing
accuracy to change. The only probable cause for one of these timers to gain
or lose time is either a) operating a 50 Hz timer on a 60 Hz supply, or
vice-versa, or b) a power outage.

http://www.allaboutcircuits.com/vol_2/chpt_13/2.html


  #7   Report Post  
Posted to alt.home.repair
dpb dpb is offline
external usenet poster
 
Posts: 12,595
Default Outdoor timer running to fast

Travis Jordan wrote:
"dpb" wrote in message ...
Travis Jordan wrote:
wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.
That timer uses a simple synchronous clock motor timer that depends on
the 60Hz AC power for accuracy. If the clock motor runs at all it is
probably keeping time. ...

The accuracy of the input doesn't guarantee the accuracy of the output if
it isn't manufactured under precise (enough) tolerances...


The synchronous motor drives a set of fixed tooth gears which in turn drive
the time display. "Manufacturing tolerances" won't cause the timing
accuracy to change. ...


That assumes the gears have accurate tooth spacing -- if they're off,
then the timing is off...

--
  #8   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 48
Default Outdoor timer running to fast

On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.

[8~{} Uncle Monster

  #10   Report Post  
Posted to alt.home.repair
dpb dpb is offline
external usenet poster
 
Posts: 12,595
Default Outdoor timer running to fast

dpb wrote:
Travis Jordan wrote:
"dpb" wrote in message ...
Travis Jordan wrote:
wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.
That timer uses a simple synchronous clock motor timer that depends
on the 60Hz AC power for accuracy. If the clock motor runs at all
it is probably keeping time. ...
The accuracy of the input doesn't guarantee the accuracy of the
output if it isn't manufactured under precise (enough) tolerances...


The synchronous motor drives a set of fixed tooth gears which in turn
drive the time display. "Manufacturing tolerances" won't cause the
timing accuracy to change. ...


That assumes the gears have accurate tooth spacing -- if they're off,
then the timing is off...


Actually, I'll agree on principle overall...was thinking of a short term
variability possibly, but on the long term, it has to run a revolution
per N cycles so not the OP's problem over 12 hours...

As noted elsewhere, the ratio of 60/50 to 13/12 is close enough to make
one wonder if OP order the wrong series number and got a 50Hz model or
perhaps it was just mislabeled...

--


  #12   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 48
Default Outdoor timer running to fast

On Jul 1, 1:21 pm, dpb wrote:
wrote:
On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.


I didn't stop initially to consider values, but (60/50)/(13/12) ~ 1.1
which is within 10% of the difference OP observed. Not an unlikely
hypothesis. Maybe he ordered the wrong subseries???

--


I was in a W.W. Grainger supply house a few years
ago where they had a new wall clock that had been
returned by a customer. The clock kept perfect time,
except for the fact that it was running backwards.
The turkeys wouldn't sell it to me.

[8~{} Uncle Monster

  #14   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 48
Default Outdoor timer running to fast

On Jul 1, 7:20 pm, dpb wrote:
wrote:
On Jul 1, 1:21 pm, dpb wrote:
wrote:
On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.
Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.
I didn't stop initially to consider values, but (60/50)/(13/12) ~ 1.1
which is within 10% of the difference OP observed. Not an unlikely
hypothesis. Maybe he ordered the wrong subseries???


--


I was in a W.W. Grainger supply house a few years
ago where they had a new wall clock that had been
returned by a customer. The clock kept perfect time,
except for the fact that it was running backwards.
The turkeys wouldn't sell it to me.


Those are pretty widely available novelties -- the barbershop I frequent
has had one for quite a long time...

--


I know that, but this one wasn't supposed to be running
backwards. I've seen the novelty clocks that are numbered
anticlockwise/counterclockwise. The odd clocks catch
your eye on a subconscious level then you look more closely
and remark WTF.

[8~{} Uncle Monster

  #15   Report Post  
Posted to alt.home.repair
dpb dpb is offline
external usenet poster
 
Posts: 12,595
Default Outdoor timer running to fast

wrote:
On Jul 1, 7:20 pm, dpb wrote:
wrote:
On Jul 1, 1:21 pm, dpb wrote:
wrote:
On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.
Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.
I didn't stop initially to consider values, but (60/50)/(13/12) ~ 1.1
which is within 10% of the difference OP observed. Not an unlikely
hypothesis. Maybe he ordered the wrong subseries???
--
I was in a W.W. Grainger supply house a few years
ago where they had a new wall clock that had been
returned by a customer. The clock kept perfect time,
except for the fact that it was running backwards.
The turkeys wouldn't sell it to me.

Those are pretty widely available novelties -- the barbershop I frequent
has had one for quite a long time...

--


I know that, but this one wasn't supposed to be running
backwards. I've seen the novelty clocks that are numbered
anticlockwise/counterclockwise. The odd clocks catch
your eye on a subconscious level then you look more closely
and remark WTF.


Bet me!

The one in the barbershop is also just like that...

--


  #16   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 5,149
Default Outdoor timer running to fast


wrote in message
oups.com...
On Jul 1, 1:21 pm, dpb wrote:
wrote:
On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.


I didn't stop initially to consider values, but (60/50)/(13/12) ~ 1.1
which is within 10% of the difference OP observed. Not an unlikely
hypothesis. Maybe he ordered the wrong subseries???

--


I was in a W.W. Grainger supply house a few years
ago where they had a new wall clock that had been
returned by a customer. The clock kept perfect time,
except for the fact that it was running backwards.
The turkeys wouldn't sell it to me.

Chuckle. A house my family had for a couple years back in the late 60s had a
built-into-the-paneled-wall kitchen clock like that. (Shaft stuck through
paneling, little brass squares that served as the numbers stuck to paneling
around it. Very Trendy for about a month in '66) Every time the power
blipped during a thunderstorm, it would start running backwards. Nobody ever
cared enough to pull it out from the access hatch in the pantry behind and
diagnose it. We just ignored it, or if company was coming, flipped the
breaker off and on.

aem sends...


  #17   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 48
Default Outdoor timer running to fast

On Jul 1, 8:37 pm, dpb wrote:
wrote:
On Jul 1, 7:20 pm, dpb wrote:
wrote:
On Jul 1, 1:21 pm, dpb wrote:
wrote:
On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.
Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.
I didn't stop initially to consider values, but (60/50)/(13/12) ~ 1.1
which is within 10% of the difference OP observed. Not an unlikely
hypothesis. Maybe he ordered the wrong subseries???
--
I was in a W.W. Grainger supply house a few years
ago where they had a new wall clock that had been
returned by a customer. The clock kept perfect time,
except for the fact that it was running backwards.
The turkeys wouldn't sell it to me.
Those are pretty widely available novelties -- the barbershop I frequent
has had one for quite a long time...


--


I know that, but this one wasn't supposed to be running
backwards. I've seen the novelty clocks that are numbered
anticlockwise/counterclockwise. The odd clocks catch
your eye on a subconscious level then you look more closely
and remark WTF.


Bet me!

The one in the barbershop is also just like that...

--


Oh, I believe you, I've seen stranger things. The
little old barbershop I frequent on a semiannual
basis (whenever I start looking like Hagar The Horrible)
has no unusual artifacts. Perhaps I shall get
them one.

[8~{} Uncle Monster

  #18   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 48
Default Outdoor timer running to fast

On Jul 1, 8:46 pm, "aemeijers" wrote:
wrote in message

oups.com...

On Jul 1, 1:21 pm, dpb wrote:
wrote:
On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.


Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.


I didn't stop initially to consider values, but (60/50)/(13/12) ~ 1.1
which is within 10% of the difference OP observed. Not an unlikely
hypothesis. Maybe he ordered the wrong subseries???


--


I was in a W.W. Grainger supply house a few years
ago where they had a new wall clock that had been
returned by a customer. The clock kept perfect time,
except for the fact that it was running backwards.
The turkeys wouldn't sell it to me.


Chuckle. A house my family had for a couple years back in the late 60s had a
built-into-the-paneled-wall kitchen clock like that. (Shaft stuck through
paneling, little brass squares that served as the numbers stuck to paneling
around it. Very Trendy for about a month in '66) Every time the power
blipped during a thunderstorm, it would start running backwards. Nobody ever
cared enough to pull it out from the access hatch in the pantry behind and
diagnose it. We just ignored it, or if company was coming, flipped the
breaker off and on.

aem sends...


Don't you just love it when devices act in an anomalous
fashion?

[8~{} Uncle Monster

  #19   Report Post  
Posted to alt.home.repair
dpb dpb is offline
external usenet poster
 
Posts: 12,595
Default Outdoor timer running to fast

wrote:
On Jul 1, 8:37 pm, dpb wrote:
wrote:
On Jul 1, 7:20 pm, dpb wrote:
wrote:
On Jul 1, 1:21 pm, dpb wrote:
wrote:
On Jul 1, 11:09 am, wrote:
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.
Sometimes the manufacturers screw up and put the wrong
timer motor into a piece of equipment. I have seen a 50hz
motor in a timer that was supposed to for 60hz. If you take
the timer out of it's case and look at the back you should
be able to see the motor which will have the voltage and
frequency printed on it.
I didn't stop initially to consider values, but (60/50)/(13/12) ~ 1.1
which is within 10% of the difference OP observed. Not an unlikely
hypothesis. Maybe he ordered the wrong subseries???
--
I was in a W.W. Grainger supply house a few years
ago where they had a new wall clock that had been
returned by a customer. The clock kept perfect time,
except for the fact that it was running backwards.
The turkeys wouldn't sell it to me.
Those are pretty widely available novelties -- the barbershop I frequent
has had one for quite a long time...
--
I know that, but this one wasn't supposed to be running
backwards. I've seen the novelty clocks that are numbered
anticlockwise/counterclockwise. The odd clocks catch
your eye on a subconscious level then you look more closely
and remark WTF.

Bet me!

The one in the barbershop is also just like that...

--


Oh, I believe you, I've seen stranger things. The
little old barbershop I frequent on a semiannual
basis (whenever I start looking like Hagar The Horrible)
has no unusual artifacts. Perhaps I shall get
them one.



I'm betting the one you saw was probably modified by the countermen
themselves as a lark, not that it was "returned"...

--
  #20   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 49
Default Outdoor timer running to fast

Travis Jordan wrote:
"dpb" wrote in message ...
Travis Jordan wrote:
wrote in message
oups.com...
I just wired up an Intermatic T103 timer. I noticed after 12 hours
the timer seems to be moving to fast (12 hours registered about 13
hours on the timer). Could I have a wiring issue or is this just a
faulty clock timer? TIA.
That timer uses a simple synchronous clock motor timer that depends on
the 60Hz AC power for accuracy. If the clock motor runs at all it is
probably keeping time. ...

The accuracy of the input doesn't guarantee the accuracy of the output if
it isn't manufactured under precise (enough) tolerances...


The synchronous motor drives a set of fixed tooth gears which in turn drive
the time display. "Manufacturing tolerances" won't cause the timing
accuracy to change. The only probable cause for one of these timers to gain
or lose time is either a) operating a 50 Hz timer on a 60 Hz supply, or
vice-versa, or b) a power outage.

http://www.allaboutcircuits.com/vol_2/chpt_13/2.html


Neither (a) or (b) would cause a synchronous motor timer to gain an
hour; (a) would cause it to gain 2.4 hours and (b) would cause it to
lose however many hours the power was off. If the gear tolerances were
off, however (tooth count or diameter off a smidge, it could well gain
an hour in twelve.

--
"Take sides! Always take sides! You may sometimes be wrong - but the man
who refuses to take sides must *always* be wrong! Heaven save us from
poltroons who fear to make a choice!" R.A. Heinlein, "Double Star"


  #21   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 1
Default Outdoor timer running to fast

replying to timnels, Kenny wrote:
I don't know what sort of timer is a T103. But I have a very old (but
excellently designed) Oasis Dundee 9 Station irrigation pump controller, which
very recently developed an issue where its digital clock was running too fast.
About an hour later, the clock would be something like 7 minutes or so ahead
of 'actual' time of day. My controller doesn't appear to have a 'crystal'
component on the circuit board. But it normally keeps the correct time even
when AC power is switched off, and powered by a back-up battery. So there must
be an oscillator circuit in my board's circuit - somewhere. The beauty of my
particular irrigation controller is that it only has two electrolytic
capacitors in it. I changed the smaller electrolytic capacitor (a 100
microFarad one). No improvement. I then changed the larger 470 microFarad one,
which fixed the issue. As we know, due to the limits of our technology -
electrolytic capacitors are probably the number 1 cause of electronic circuit
failures in circuits. Since my particular board had only two capacitors, it
allowed me to sort things out fairly quickly. The interesting thing is - the
electrolytic capacitors do not necessarily need to be bulging (or physically
broken) when they go bad or fail. But, they often will have a bulging top if
they've failed. So, if your timer has electrolytic capacitors in it.... check
them out.

--
for full context, visit https://www.homeownershub.com/mainte...st-230136-.htm


  #22   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 3,297
Default Outdoor timer running to fast

On 2/22/2017 6:44 PM, Kenny wrote:
replying to timnels, Kenny wrote:
I don't know what sort of timer is a T103. But I have a very old (but
excellently designed) Oasis Dundee 9 Station irrigation pump controller,
which
very recently developed an issue where its digital clock was running too
fast.
About an hour later, the clock would be something like 7 minutes or so
ahead
of 'actual' time of day. My controller doesn't appear to have a 'crystal'
component on the circuit board. But it normally keeps the correct time even
when AC power is switched off, and powered by a back-up battery. So
there must
be an oscillator circuit in my board's circuit - somewhere. The beauty
of my
particular irrigation controller is that it only has two electrolytic
capacitors in it. I changed the smaller electrolytic capacitor (a 100
microFarad one). No improvement. I then changed the larger 470
microFarad one,
which fixed the issue. As we know, due to the limits of our technology -
electrolytic capacitors are probably the number 1 cause of electronic
circuit
failures in circuits. Since my particular board had only two capacitors, it
allowed me to sort things out fairly quickly. The interesting thing is -
the
electrolytic capacitors do not necessarily need to be bulging (or
physically
broken) when they go bad or fail. But, they often will have a bulging
top if
they've failed. So, if your timer has electrolytic capacitors in it....
check
them out.

You morons have to stop responding to 10 year old posts.
  #23   Report Post  
Posted to alt.home.repair
external usenet poster
 
Posts: 1,196
Default Outdoor timer running to fast

On 2/22/2017 7:44 PM, Frank wrote:
On 2/22/2017 6:44 PM, Kenny wrote:
replying to timnels, Kenny wrote:
I don't know what sort of timer is a T103. But I have a very old (but
excellently designed) Oasis Dundee 9 Station irrigation pump controller,
which
very recently developed an issue where its digital clock was running too
fast.
About an hour later, the clock would be something like 7 minutes or so
ahead
of 'actual' time of day. My controller doesn't appear to have a 'crystal'
component on the circuit board. But it normally keeps the correct time
even
when AC power is switched off, and powered by a back-up battery. So
there must
be an oscillator circuit in my board's circuit - somewhere. The beauty
of my
particular irrigation controller is that it only has two electrolytic
capacitors in it. I changed the smaller electrolytic capacitor (a 100
microFarad one). No improvement. I then changed the larger 470
microFarad one,
which fixed the issue. As we know, due to the limits of our technology -
electrolytic capacitors are probably the number 1 cause of electronic
circuit
failures in circuits. Since my particular board had only two
capacitors, it
allowed me to sort things out fairly quickly. The interesting thing is -
the
electrolytic capacitors do not necessarily need to be bulging (or
physically
broken) when they go bad or fail. But, they often will have a bulging
top if
they've failed. So, if your timer has electrolytic capacitors in it....
check
them out.

You morons have to stop responding to 10 year old posts.

Yea but, how do you know they are 10 years old. I've just looked and
can't find a real date. Yes I know that I could go to the site shown in
the original post, but why should we have to play detective on each
post? And, using FF, how do I block all of the posts starting with
"". It didn't seem to work and blocked a whole bunch of posts that
didn't start with .
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Wiring Outdoor Timer [email protected] Home Repair 4 June 23rd 07 03:22 PM
Stanton STR8-100 running fast. Odrec Electronics Repair 3 May 13th 07 08:30 PM
Running outdoor Christmas lights without an outdoor outlet PM Home Repair 5 December 17th 06 05:12 AM
Running outdoor Christmas lights without an outdoor outlet PM Home Ownership 2 December 17th 06 12:56 AM
How to reset outdoor light timer [email protected] Home Ownership 7 May 5th 05 07:57 PM


All times are GMT +1. The time now is 01:53 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"