I havea Fridgerdaier front loading washing machine and since it was
new the door has buzzed after closing and when running a cycle. At
first it was tolerable but since then and now out of warrantee it
makes an awful buzz. Having takne it apart it has a simple solenoid
that is supposied to hold tight. Since the solenoid runs on 60 Hz
directly it loses it's magnetic field twice a cycle. Hence the buzz.
My ? is how did they expect it to be quiet when designed and how can I
be sure the new one ( $65!! ) will be any different.
I am sure that I can modify/add circuitry to the system , for about
$5.00 so that the solenoid is DC powered, at a lower voltage . Can
anyone offer their input to this.
I have searched the internet but I seem to be the only person with
this washing machine problem!

(ron doctors) writes:

I havea Fridgerdaier front loading washing machine and since it was
new the door has buzzed after closing and when running a cycle. At
first it was tolerable but since then and now out of warrantee it
makes an awful buzz. Having takne it apart it has a simple solenoid
that is supposied to hold tight. Since the solenoid runs on 60 Hz
directly it loses it's magnetic field twice a cycle. Hence the buzz.
My ? is how did they expect it to be quiet when designed and how can I
be sure the new one ( $65!! ) will be any different.
I am sure that I can modify/add circuitry to the system , for about
$5.00 so that the solenoid is DC powered, at a lower voltage . Can
anyone offer their input to this.
I have searched the internet but I seem to be the only person with
this washing machine problem!

AC solenoids have a thick copper "shading" ring on the pole piece. It's
purpose is to delay the decay of the magnetic field so that the solenoid
will produce a more constant pull even though it's AC.

Assuming that the shading ring is present, it may just be a matter of
repositioning it for a slightly shorter or longer throw.

Of course, ther's no guarantee that the new part will be any better!

--- sam | Sci.Electronics.Repair FAQ Home Page: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Site Info: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: The email address in this message header may no longer work. To
contact me, please use the feedback form on the S.E.R FAQ Web sites.

Sam Goldwasser wrote in message ...
(ron doctors) writes:

I havea Fridgerdaier front loading washing machine and since it was
new the door has buzzed after closing and when running a cycle. At
first it was tolerable but since then and now out of warrantee it
makes an awful buzz. Having takne it apart it has a simple solenoid
that is supposied to hold tight. Since the solenoid runs on 60 Hz
directly it loses it's magnetic field twice a cycle. Hence the buzz.
My ? is how did they expect it to be quiet when designed and how can I
be sure the new one ( $65!! ) will be any different.
I am sure that I can modify/add circuitry to the system , for about
$5.00 so that the solenoid is DC powered, at a lower voltage . Can
anyone offer their input to this.
I have searched the internet but I seem to be the only person with
this washing machine problem!

AC solenoids have a thick copper "shading" ring on the pole piece. It's
purpose is to delay the decay of the magnetic field so that the solenoid
will produce a more constant pull even though it's AC.

Assuming that the shading ring is present, it may just be a matter of
repositioning it for a slightly shorter or longer throw.

Thanks for adding this.. Id id check teh spcing on the solenoid and
the plunger di not seat fully, with some grinfing I made the fit
better and yes the buzz is reduced. However it still buzzes sometimes.
I have now made acircuit cost under$5.00 that does this:
1. It charges up a 22 mfd cap to 160 volts ( 120 x 2.8 )from the 120
line
2. Discharges the cap thru. the solenoid via sensitive-gate SCR.
3. Maintains the solenoid at about 16 volts by using a series resistor
to limit the current.
Parts are easy to get at Mouser.com and simple to solder together. The
washer door solenoid is now completely SILENT!! holds better ( DC )
and it closes very well.
If anyone is interested in the complete circuit I will post it, let me
know.