A DIY & home improvement forum. DIYbanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » DIYbanter forum » Do - it - Yourself » Electronics Repair
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Need help programming RCA SystemLink 4 remote



 
 
LinkBack Thread Tools Display Modes
  #1  
Old December 10th 03, 01:38 AM
Ken_B
external usenet poster
 
Posts: n/a
Default Need help programming RCA SystemLink 4 remote

I have a SystemLink 4 remote, and need to control an A/V receiver. The
instruction book has a list of audio codes, but the instructions are screwed
up.

The only device buttons are TV, VCR, Satellite, and AUX. Instructions say
audio devices can be assigned to AUX.

Instructions for assigning other devices to AUX say press and hold Code
Search Button until light comes on, then press AUX, after which the light
will blink and stay lit. Then the instructions say to PRESS THE BUTTON FOR
THE DEVICE you want to program. But there is NO AUDIO BUTTON!

I've tried just pressing AUX then putting in audio codes, but nothing works.
Tried on three different brands of A/V receivers.

Anybody know how to make this remote work audio? Thanks.


Ads
  #2  
Old December 10th 03, 04:07 PM
sofie
external usenet poster
 
Posts: n/a
Default Need help programming RCA SystemLink 4 remote

Ken B:
The instructions are correct....... AUX is the "audio" button. More than
likely the codes listed in your instructions are not inclusive of the
equipment you want to control..... have you tried the "auto-search" to find
a possible code? Look in your instructions...... it will require that the
equipment be turned on and multiple presses of the remote control power
button to find a proper code...... refer to your instructions for the
proper button sequence.
As a final note.... it is possible that you may need a factory original
remote to control your A/V receiver.
--
Best Regards,
Daniel Sofie
Electronics Supply & Repair
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -


"Ken_B" ken5229"at"softhome.net wrote in message
...
I have a SystemLink 4 remote, and need to control an A/V receiver. The
instruction book has a list of audio codes, but the instructions are

screwed
up.

The only device buttons are TV, VCR, Satellite, and AUX. Instructions say
audio devices can be assigned to AUX.

Instructions for assigning other devices to AUX say press and hold Code
Search Button until light comes on, then press AUX, after which the light
will blink and stay lit. Then the instructions say to PRESS THE BUTTON FOR
THE DEVICE you want to program. But there is NO AUDIO BUTTON!

I've tried just pressing AUX then putting in audio codes, but nothing

works.
Tried on three different brands of A/V receivers.

Anybody know how to make this remote work audio? Thanks.




  #3  
Old December 11th 03, 07:37 PM
Ken_B
external usenet poster
 
Posts: n/a
Default Need help programming RCA SystemLink 4 remote

I tried the search function to no avail. Guess you're right about me needing
the original remote. Thanks.

Ken

"sofie" wrote in message
...
Ken B:
The instructions are correct....... AUX is the "audio" button. More

than
likely the codes listed in your instructions are not inclusive of the
equipment you want to control..... have you tried the "auto-search" to

find
a possible code? Look in your instructions...... it will require that

the
equipment be turned on and multiple presses of the remote control power
button to find a proper code...... refer to your instructions for the
proper button sequence.
As a final note.... it is possible that you may need a factory original
remote to control your A/V receiver.
--
Best Regards,
Daniel Sofie
Electronics Supply & Repair
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -


"Ken_B" ken5229"at"softhome.net wrote in message
...
I have a SystemLink 4 remote, and need to control an A/V receiver. The
instruction book has a list of audio codes, but the instructions are

screwed
up.

The only device buttons are TV, VCR, Satellite, and AUX. Instructions

say
audio devices can be assigned to AUX.

Instructions for assigning other devices to AUX say press and hold Code
Search Button until light comes on, then press AUX, after which the

light
will blink and stay lit. Then the instructions say to PRESS THE BUTTON

FOR
THE DEVICE you want to program. But there is NO AUDIO BUTTON!

I've tried just pressing AUX then putting in audio codes, but nothing

works.
Tried on three different brands of A/V receivers.

Anybody know how to make this remote work audio? Thanks.






 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
TV Remote Control rubber pad(UR50CT1071) used in remote control for Panasonic TV Model TX-29GF10X Steve Electronics Repair 4 November 1st 03 02:27 PM
Toshiba Remote Programming Codes Tony P. Electronics Repair 0 October 31st 03 01:54 PM
NEW ORION VCR AND RCA UNIVERSAL REMOTE James Electronics Repair 2 October 14th 03 06:44 AM
broken Toshiba remote control? happy150 Electronics Repair 3 August 25th 03 06:38 AM


All times are GMT +1. The time now is 05:42 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.SEO by vBSEO ©2010, Crawlability, Inc.
Copyright 2004-2014 DIYbanter.
The comments are property of their posters.